♥♥ 2017 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 642-813 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Actual of 642-813 exam question materials and braindump for Cisco certification for examinee, Real Success Guaranteed with Updated 642-813 pdf dumps vce Materials. 100% PASS implementing cisco switched networks exam Today!
2016 Sep ccnp switch 642-813 pdf free download:
Q91. Refer to the exhibit.
What happens when one more user is connected to interface FastEthernet 5/1?
A. All secure addresses age out and are removed from the secure address list. The security violation counter increments.
B. The first address learned on the port is removed from the secure address list and is replaced with the new address.
C. The interface is placed into the error-disabled state immediately, and an SNMP trap notification is sent.
D. The packets with the new source addresses are dropped until a sufficient number of secure MAC addresses are removed from the secure address list.
Q92. In which three HSRP states do routers send hello messages? (Choose three.)
Q93. CORRECT TEXT
You have been tasked with configuring multilayer SwitchC, which has a partial configuration and has been attached to RouterC as shown in the topology diagram.
You need to configure SwitchC so that Hosts H1 arid H2 can successful ping the server S1. Also SwitchC needs to be able to ping server SI.
Due to administrative restrictions and requirements you should not add/delete vlans or create trunk links Company policies forbid the use of static or default routing All routes must be learned via EIGRP 65010 routing protocol.
You do not have access to RouteC, RouterC is correctly configured. No trunking has been configured on RouterC.
Routed interfaces should use the lowest host on a subnet when possible. The following subnets are available to implement this solution:
Hosts H1 and H2 are configured with the correct IP address and default gateway.
SwitchC uses Cisco as the enable password.
Routing must only be enabled for the specific subnets shown in the diagram.
Note: Due to administrative restrictions and requirements you should not add or delete VLANs, changes VLAN port assignments or create trunks. Company policies forbid the use of static or default routing. All routes must be learning via the EIGRP routing protocol.
Answer: Here are Step by Step Configuration:
On switch C:
router eigrp 65010
network 172.16.1.0 0.0.0.255
network 192.168.3.32 0.0.0.31
network 192.168.3.64 0.0.0.31
Q94. Refer to the exhibit.
Assume that Switch_A is active for the standby group and the standby device has only the default HSRP configuration. Which statement is true?
A. If port Fa1/1 on Switch_A goes down, the standby device takes over as active.
B. If the current standby device had the higher priority value, it would take over the role of active for the HSRP group.
C. If port Fa1/1 on Switch_A goes down, the new priority value for the switch would be 190.
D. If Switch_A had the highest priority number, it would not take over as active router.
Q95. Refer to the exhibit.
An attacker is connected to interface Fa0/11 on switch A-SW2 and attempts to establish a DHCP server for a man-in-middle attack. Which recommendation, if followed, would mitigate this type of attack?
A. All switch ports in the Building Access block should be configured as DHCP trusted ports.
B. All switch ports in the Building Access block should be configured as DHCP untrusted ports.
C. All switch ports connecting to hosts in the Building Access block should be configured as DHCP trusted ports.
D. All switch ports connecting to hosts in the Building Access block should be configured as DHCP untrusted ports.
E. All switch ports in the Server Farm block should be configured as DHCP untrusted ports.
F. All switch ports connecting to servers in the Server Farm block should be configured as DHCP untrusted ports.
Down to date certprepare 642-813:
Q96. Refer to the exhibit.
Which statement is true?
A. Cisco Express Forwarding load balancing has been disabled.
B. SVI VLAN 30 connects directly to the 10.1.30.0/24 network due to a valid glean adjacency.
C. VLAN 30 is not operational because no packet or byte counts are indicated.
D. The IP Cisco Express Forwarding configuration is capable of supporting IPv6.
Q97. Which two steps are necessary to configure inter-VLAN routing between multilayer switches? (Choose two.)
A. Configure a dynamic routing protocol.
B. Configure SVI interfaces with IP addresses and subnet masks.
C. Configure access ports with network addresses.
D. Configure switch ports with the autostate exclude command.
E. Document the MAC addresses of the switch ports.
Q98. What is the effect of configuring the following command on a switch?
Switch(config) # spanning-tree portfast bpdufilter default
A. If BPDUs are received by a port configured for PortFast, then PortFast is disabled and the BPDUs are processed normally.
B. If BPDUs are received by a port configured for PortFast, they are ignored and none are sent.
C. If BPDUs are received by a port configured for PortFast, the port transitions to the forwarding state.
D. The command enables BPDU filtering on all ports regardless of whether they are configured for BPDU filtering at the interface level.
Q99. DRAG DROP
Drag the steps on the left that should be part of a VLAN-based verification plan to the spaces on the right. Not all choices will be used.
Q100. Refer to the exhibit.
Host A and Host B are connected to the Cisco Catalyst 3550 switch and have been assigned to their respective VLANs. The rest of the 3550 configuration is the default configuration. Host A is able to ping its default gateway, 10.10.10.1, but is unable to ping Host B. Given the output in the exhibit, which statement is true?
A. HSRP must be configured on SW1.
B. A separate router is needed to support inter-VLAN routing.
C. Interface VLAN 10 must be configured on the SW1 switch.
D. The global configuration command ip routing must be configured on the SW1 switch.
E. VLANs 10 and 15 must be created in the VLAN database mode.
F. VTP must be configured to support inter-VLAN routing.